Recurring Service Plans

 

 

What're your concepts about How to Install a Bathtub?

Mounting a bathtub isn't precisely rocket science, however it does call for solid plumbing, woodworking, and often, tiling abilities. Replacing an old tub with a brand-new one is also a moderately tough task. If the old tub is readily easily accessible, the job can relocate speedily; if you have to open up a wall surface to get rid of the old bathtub and also place the brand-new bath tub, the job is much harder. In either case, the project is within a home handyman's skills, although you will need a helper to vacate the old bathtub and also set in the new one. Ensure you have qualified yourself for the task and also fit trying it. Rather than hiring a specialist to take over a halfway-completed project, it is much better to take into consideration using one before you begin. Possibilities are you might require a professional plumber to make tube connections.
This short article will certainly aid you set up a brand-new bath tub in your washroom if you have already purchased a new bathtub and also do not require to transform the arrangement of your previous supply of water pipes.
Your tools and material list need to comprise the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Blade


• Measuring tape


• Pipeline Caps


 

Removing Old Taps

If you require to change old taps with brand-new ones as a part of your setup, after that the first thing you need to do is disconnect the water system. After doing so, activate the taps to drain any type of water continuing to be in the system. The process of eliminating the existing faucets can be fairly problematic due to the limited accessibility that is often the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the faucets. Have a cloth ready for the staying water that will certainly come from the pipes. As soon as the supply pipelines have been removed, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from transforming throughout this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Before carrying on to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the brand-new taps to fit.

 

 

Fitting New Touches

If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to avoid damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a link to the existent supply pipes.
If you require to fit a monobloc, then you will call for reducing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin ensuring that the washers are in area in between the faucet and the sink. Safeguard the tap in position with the manufacturer offered backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The former type needs to be connected to the tap finishes first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.

 

 

Mounting the Bathtub

Utilizing both wood boards under its feet, place the tub in the needed placement. The wooden boards are useful in uniformly spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 tiny factors.
The next goal is to guarantee that the tub is leveled all round. This can be attained by checking the spirit level as well as changing the feet on the bath tub till the spirit level reads level.
To set up faucets, fit all-time low of the outermost adaptable tap connector to the suitable supply pipe by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water supply and check all joints as well as new pipework for leaks as well as tighten them if needed. Load the bath tub as well as additionally examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, fix the bath paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bathtub should wait until the bathtub has actually been made use of at the very least when as this will certainly resolve it right into its last setting.

 

 

Getting ready for the Setup

First of all, the supporting frame supplied with the bathroom must be fitted (if needed) according to the producer's instructions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is important to see to it that if the tap comes with a plastic washer, it is fitted in between the bath and the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps device to avoid stress on the bathtub.
Fit the flexible faucet ports to the bottom of the two taps making use of 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you use every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must now be ready to be suited its final placement.

 

 

Tiling Around the Bathtub

In the location where the bath satisfies the floor tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to crack a stiff seal, creating the water to permeate the wall surface between the bath and also the tiling, leading to issues with dampness as well as feasible leakages to the ceiling below.
You can select from a selection of coloured sealants to assimilate your components and fittings. They are marketed in tubes and cartridges, as well as are capable of securing gaps up to a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill the bathtub with water prior to securing, to permit the movement experienced when the tub remains in usage. The sealer can crack relatively very early if you do not think about this movement before sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally easily available on the market. It is a good idea to fit the floor tiles making use of water-resistant or waterproof adhesive and grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Hopefully you enjoyed our excerpt on Tools You Need to Install a New Bathtub . Thanks for finding the time to read our post. Do you know another person who is looking into the subject? Take a moment to share it. Thank-you for taking the time to read it.

Maintenance Sign-Up